Product Tested

front label

Click above for larger image

back label

Click above for larger image

Speedway LLC

Company and Product Information

Corporate Office:
Speedway LLC
500 Speedway Drive
Enon, OH 45323

Website(s): www.speedway.com

Headquartered in Enon, Ohio, Speedway LLC is a gasoline and convenience store company with approximately 2,740 locations in 22 states. Speedway's mission is to be the customers' first choice for value and convenience. Speedway LLC is a subsidiary of Marathon Petroleum Corporation

Speedway
SAE 5W-20 Motor Oil

Product: Speedway
Viscosity Grade: SAE 5W-20
Labeled: API SN PLUS/ILSAC GF-5

Distributed By: Speedway LLC

Purchased at: Linden, NJ

Date of purchase: 4/25/2019

 

Website(s): www.speedway.com

Test Results and Assessment:

The results of the tests conducted on this sample meet the SAE J300 specifications for the SAE Viscosity Grade listed on the product label, and are consistent with the listed API Service Categories.

.

bottle icon Physical Properties pass
Elemental Analysis pass
Labeling warning
Viscosity @ 100°C, cSt (ASTM D445)

The results of the Kinematic Viscosity @ 100ºC test conducted on this sample meet the requirements of SAE J300.
FusionCharts XT will load here!
Cold Cranking Viscosity, mPa s (cP) (ASTM D5293)

The results of the Cold Cranking Viscosity test conducted on this sample meet the requirements of SAE J300.
FusionCharts XT will load here!
Phosphorus, ppm (ASTM D5185)

The results of the Phosphorus test conducted on this sample meet the requirements of API SN/ILSAC GF-5.
FusionCharts XT will load here!

Note1: Although laboratory tests alone cannot be used to establish if engine oil meets an API Service Category, they can be used to determine if it doesn't. Note2: The specification for cold cranking viscosity includes only a maximum value; the minimum value shown in the “standard” area of the chart is truncated for illustrative purposes.

PHYSICAL TESTS (click for test details) - a Standard Speedway
TBN, mg KOH/g (ASTM D2896) 9.28
Viscosity @ 100ºC, cSt (ASTM D445) 6.9 to <9.3 8.6
Viscosity @40ºC, cSt (ASTM D445) 50.6
Viscosity Index (ASTM D2270) 147
Viscosity @-30ºC mPa s (cP) (ASTM D5293) 6,600 Max 5,755
ELEMENTAL ANALYSIS (click for test details) - a, b
Additives
Calcium, ppm 1,427
Magnesium, ppm 977
Phosphorus, ppm 600 to 800 -d 723
Zinc, ppm 847
Molybdenum,  ppm 52
Barium, ppm <1
Boron, ppm <1
Silicon, ppm 8
Potassium, ppm 2
Manganese, ppm <1
Titanium, ppm <1
Copper, ppm <1
Sodium, ppm 1
Vanadium, ppm <1
Contaminants
Silver, ppm <1
Aluminum, ppm <1
Chromium, ppm <1
Iron, ppm 1
Nickel, ppm <1
Lead, ppm <1
Antimony, ppm <1
Tin, ppm <1
  1. Standards, shown in yellow are established by API, SAE and others.
  2. Test Method for metal analysis is ASTM D5185.
  3. This specification is expressed to two significant figures, therefore results up to 15.5 are considered on specification.
  4. This specification is expressed to one significant figure, therefore results between 550 and 849 are considered on specification.